grounds on the factory floor, in the shop. Continually tests its battery and its circuit integrity with a periodic double flash visual indication using Fluke Voltbeat™ technology. Two-Year Warranty. (USA) Features Detects line voltage from 90VAC - 600VAC (1AC-AI-II) Voltbeat™ technology and continuous self-test - so you always know it's working Upon detection, tip glows and beeper sounds CAT IV 1000V for added protection Expanded range: 90V to 1000V AC or 200V to 1000VAC depending on model 20V to 90V AC control circuit model also available Two-year warranty  (less)

to carry a separate instrument. Optional magnetic hanger for easy set-up and viewing while freeing your hands for other tasks. Large digit display with bright, two-level backlight makes the 80- Series V significantly easier to read than older models. Features: True-rms ac voltage and current for accurate measurements on non linear signals. Selectable filter for accurate voltage and frequency measurements on motor drives. 0.05 % dc accuracy. 6000 counts, 3-3/4 digits. 4-1/2 digit mode for precise measurements (20,000 counts). Measure up to 1000 V ac and dc. Measure up to 10 A, 20 A for up to 30 seconds. Built in thermometer lets you carry one less tool (TC probe included). Frequency to 200 kHz and % duty cycle. Resistance, continuity and diode test. 10,000 µF capacitance range for components and motor caps. Min/Max-Average recording with Min/Max Alert to capture variations automatically. Peak capture to record transients as fast as 250 µs. Relative mode to remove test lead interference from low ohms measurements. Auto and manual ranging for maximum flexibility. Touch Hold to capture stable readings avoiding noisy signals. Large display digits and two-level bright white backlight for increased visibility. Analog bargraph for fast changing or unstable signals. Input Alert provides audible warning against wrong use of input jacks. Improved selectable sleep mode for long battery life. Access door for fast battery changes without breaking the calibration seal. "Classic" design with new removable holster with built in test lead and probe storage. Lifetime warranty.  (less)

voltage selection - LoZ helps prevent false readings due to ghost voltage - Large white LED backlight to work in poorly lit areas - True-rms for accurate measurements on non-linear loads - Measures 20 A (30 seconds momentary; 10 A continuous) - 10,000 uF capacitance range- Resistance, continuity, frequency and - Min/Max/Average with elapsed time to record signal fluctuations - Compact ergonomic design for one-handed operation - Compatible with optional magnetic hanger (ToolPak) for hands free operation - CAT III 600 V safety rated - 3 Year Warranty  (less)

Accuracy ±(5%+2.5A), 5A to 400A, DC to 62 Hz. Useable to 400 Hz.  (less)

(psig of Hg) or metric (kPa or cm Hg) units Measures pressure to 3447 kPa (500 psig) One year warranty  (less)

FlukeView forms software. TrendCapture plots measurements as single line to help detect anomalies. Advanced features are combined with True-RMS 50,000 count 1/4 VGA dot matrix display. Features: 50,000 count, 320 x 240 dot matrix LCD display with backlight. Multiple sets of measurement information can be read on display Record events and trends helpful for troubleshooting intermittent problems or profiling loads Name and recall saved measurements made in the field Optical USB PC communication interface allow for easy document download to FlukeView Forms software F1-F4 Soft Keys provide flexible user function menus "i" info button on meter actives help screen for measurement functions Navigation keys allow you to quickly select menu choices and scroll through the information screens Field upgradeable and expandable as new capabilities become available Limited lifetime warranty Specifications True-rms readings: AC + DC Basic DC accuracy: 0.025% Voltage AC/DC: 50mV, 500mV, 5V, 50V, 500V, 1000V Current AC/DC: 500µA, 5000&microA, 50mA, 400mA, 5A, 10A Resistance: 500Ω, 5kΩ, 50kΩ, 500kΩ, 5MΩ 50MΩ, 500MΩ Frequency: 999.99 kHz Capacitance: 1nF, 10nF, 100nF, 1&  (less)

voltage and current measurements 0.09% basic accuracy 6000 count resolution Digital display with analog bargraph and backlight Manual and automatic ranging Display Hold and Auto Hold Frequency and capacitance measurements Resistance, continuity and diode measurements Temperature measurements Min-max-average recording Smoothing mode allows filtering of rapidly changing inputs Easy battery exchange without opening the case Closed case calibration through front panel Ergonomic case with integrated protective holster EN61010-1 CAT III 1000V / CAT IV 600V Measures twice as fast as other multimeters Fluke 1AC-II / 1LAC-II VoltAlert The pocket-sized voltage detector The next generation VoltAlert™ AC non-contact voltage testers from Fluke are easy to use - just touch the tip to a terminal strip, outlet, or supply cord. When the tip glows red and the unit beeps, you know there's voltage present. Electricians, maintenance, service, safety personnel, and homeowners can quickly test for energized circuits in the workplace or at home. Features: Voltbeat™ technology and continuous self-test - so you always know it's working Upon detection, tip glows and beeper sounds CAT IV 1000 V for a  (less)

multimeters (DMM)  (less)

standards. Measures: Wide 1000V measurement range Average responding ac measurements 0.3% accuracy 10A continuous Frequency and capacitance Resistance and continuity Includes: Test leads, 9V battery, holster, user manual. Limited Lifetime Warranty.(USA)  (less)

and diode measurements Min-max-average recording Smoothing mode allows filtering of rapidly changing inputs Easy battery exchange without opening the case Closed case calibration through front panel Ergonomic case with integrated protective holster EN61010-1 CAT III 1000V / CAT IV 600V Measures twice as fast as other multimeters Specifications Voltage DC Accuracy*: ± (0.09%+2) Max. Resolution: 0.1 mV Maximum: 1000 V Voltage AC Accuracy*: ± (1.0%+3) Max. Resolution: 0.1 mV Maximum: 1000 V Current DC Accuracy*: ± (1.0%+3) Max. Resolution: 0.01 mA Maximum: 10 A Current AC Accuracy*: ±: (1.5%+3) Max. Resolution: 0.01 mA Maximum: 10 A Resistance Accuracy*: ± (0.9%+1) Max. Resolution: 0.1 Ω Maximum: 50 MΩ Capacitance Accuracy*: ± (1.2%+2) Max. Resolution: 1 nF Maximum: 10,000 µF Frequency Accuracy*: ± (0.1%+1) Max. Resolution: 0.01 Hz Maximum: 100 kHz *Note: Accuracies are best accuracies for each function Environmental Specifications Operating Temperature: -10°C to +50°C Storage Temperature: -30°C to +60°C Humidity (Without Condensation): 0% - 90% (0°C - 35°C) 0% - 70% (35°C -50°C) S  (less)

by load switching and faults on industrial circuits and complies with second edition IEC and ANSI electrical safety standards. 4-1/2 digit mode for precise measurements µF capacitance range for components and motor caps Measure up to 1000V AC and DC. Measure up to 10 A, 20 A for up to 30 seconds Auto and manual ranging for maximum flexibility Analog bar graph Resistance, continuity and diode test Frequency to 200 kHz and % duty cycle Min/Max and Average recording to capture variations automatically Removable holster with built-in test lead and probe storage Limited Lifetime Warranty CLASS="CHART"> ALIGN="CENTER">Specifications83-V 87-V TRMS ID="HEAD">Voltage DC Maximum Voltage: align="left"> 1000V ID="HEAD">Basic Accuracy: width="113">±(0.1%+1) width="72">±(0.05%+1) Maximum Resolution: 100 µV 10µV Voltage AC Maximum Voltage: colspan="2">1000V Basic Accuracy: ±(0.5%+2) ±(0.7%+2) True RMS AC Bandwidth: valign="top">5kHz valign="top">20kHz*  colspan="2">*with low pass filter; 3db @ 1kHz Maximum Resolution: valign="top">0,1 mVCurrent DC Maximum A  (less)

inductive pickup (included).- Millisecond pulse width measurements for fuel injectors.- Frequency to 200 kHz and % duty cycle.- Measure up to 1000 V ac and dc.- Measure up to 10 A, 20 A for up to 30 seconds.- 4_digits for precise measurements.Features:- Magnetic hanger to attach meter to the vehicle and free your hands for other tasks.- Min/Max-Average recording with Min/Max Alert to capture variations automatically.- Relative mode to remove test lead interference from low ohms measurements.- Large display digits and two-level bright white backlight for increased visibility.- Analog bargraph for fast changing or unstable signals.- Access door for fast battery changes without opening up the case.- Limited lifetime warrantee, UL and CSA approved.- Made in USA.88V/A Combo Kit includes:- 88V Automotive Multimeter.- 1.5m long heat resistant silicone test leads.- Removable test probes to pierce corroded terminals.- Alligator clips.- Magnetic hanger to position and hold meter to steel surfaces.- Temperature probe.- Inductive RPM pick-up probe.- Two back probe pins.- Insulation piercing clip (red)- Durable case.  (less)

with safety shrouded, standard diameter banana plugs Right angle connector on both ends Reinforced strain relief 1.5 meter silicone-insulated wire resists heat & cold CAT IV 600 V, CAT III 1000 V, 10 A rating. UL listed One year warranty  (less)

The clamp is compatible with most Fluke multimeters or any other current measurement device that accepts 4mm-shrouded banana plugs and has an AC milliamp range. The division ratio is 1000:1. High safety AC current clamp with BNC output Companion to your scope or power quality meter to measure up to 400 A AC. Only current clamp available with a CAT IV 600 V / CAT III 1000 V safety rating. Specially designed to offer maximum utility in a compact shape. Take accurate current readings without breaking the circuit. Soft non-slippery overmold handle. Optional PM9081/001 BNC/Banana adapter for DMM's Two ranges: 40 A & 400 A, 10 & 1 mV/Amp output. Max. conductor diameter 32 mm. Specifications Nominal current range: 40 A Range: 0.5A to 40 A 400A Range: 5 A to 400 A Basic accuracy: 40 A Range 2% + 0.015 A (45-400 Hz) 400 A Range 2% + 0.04 A (45-400 Hz) Phase Shift: 40 A Range: 0.5 to 1 A: Unspecified 1 A to 5 A: 4° 5 A to 10 A: 3° 10 A to 20 A: 3° 20 A to 40 A: 2° 40 A to 400 A: NA 400 A Range 5 A to 10 A: Unspecified 10 A to 20 A: 2° 20 A to 40 A: 2° 40 A to 400 A: 1.5° Typical Bandwidth: 40 A Range: 5 Hz - 10 kHz 400 A Range: 5 Hz - 10 kHz Output level(s): 40 A Range: 10 mV/A 400 A Range: 1 mV/A Crest Factor: 40 A Range: 3 400 A  (less)

MAX feature captures intermittent events as short as 250 microseconds :The DMM is protected from bumps and bounces by an integrated removable holster and a magnetic hanger holds the meter for viewing, while freeing the hands for other tasks :Includes accessories:::TL224 1.5 m long heat resistant silicone test leads :TP220 Removable Test Probes for probing corroded terminals :AC285 Wide Jaw Alligator Clips :Two automotive back probe pins :Insulation piercing probe :TPAK Magnetic Hanger to position and hold meter to steel surfaces :RPM80 Inductive RPM Pick-Up Probe :80BK Temperature Probe :User's manual and getting started guide :Product manuals on CD :C800 Durable Carrying Case  (less)

connector. A dual banana to BNC adapter is supplied to allow the i200s to be connected to multimeters with banana inputs. Companion to your scopemeter, power quality meter or digital multimeter to measure up to 200 A AC Included adapter for DMM's Two ranges: 20 A & 200A, 10 or 100 mV/ Amp output Take accurate current readings without breaking the circuit Max. conductor diameter 20 mm CAT III 600V safety rating Specifications Nominal current range: 20 A 200 A Continuous current range: 0.1 A - 24 A 0.5 A - 200 A Maximum Non-Destructive Current: 240 A Lowest measurable current: 0.1 A Basic accuracy: 1.5% +0.5 A (48-65 Hz) (% reading + floorspec) Useable frequency: 40 Hz - 10 kHz Output level(s) 100 mV/A 10 mV/A Safety Specifications Safety: CAT III, 600 V Maximum voltage: 600 V AC Mechanical & General Specifications Warranty: 1 year Maximum conductor diameter: 20 mm Maximum conductor size (busbar): 20 x 5 mm Output cable length: 2.0 m BNC Adapter: Yes BNC to banana adapter included: Yes  (less)

and flame sensors. Fluke 116 True RMS Digital Multimeter Features: True RMS .5% accuracy 28% larger digits 6000 counts Bargraph Backlit Min-max recording Display hold Ergonomic, compact shape Voltage Resistance Detect AC voltage without carrying a second tool Works down to 24VAC in bare wire applications AutoV™ Automatic volts detection Automatically determines AC or DC voltage eliminating guesswork Correctly displays voltage measurement without extra steps LoZ™ Low impedance Reduces chance of false readings due to ghost voltage Safer troubleshooting Specificatons Maximum voltage between any terminal and earth ground: 600 V Surge protection 6 kV peak per IEC 61010-1 600 V CAT III, Pollution Degree 2 Display Digital: 6,000 counts, updates 4 per second Bar graph: 33 segments, updates 32 per second Operating Temperature: -10°C to + 50°C Storage Temperature -40°C to + 60°C Battery type: 9 volt Alkaline, NEDA 1604A/ IEC 6LR61 Battery Life: 400 hours typical, without backlight Accuracy Specifications DC millivolts Range: 600.0 mV Resolution: 0.1 mV Accuracy: ± ([% of reading] + [counts]): 0.5% + 2 DC volts Range/Resolution: 6.000 V / 0.001 V Rang  (less)

100 mA to 1000 A rms, 5 Hz to 100 kHz without breaking into the circuit A passive filter eliminates noise and ring on rapidly rising di/dt waveform, ensuring accurate screen displays Connects directly to an oscilloscope through a reinforced coaxial cable and an insulated BNC connector Can be used with Multimeters with optional PM9081/001 BNC/Banana adapter One year warranty Specifications: Current range: AC 100A to 1000A Frequency Response: 5 Hz to 100 kHz Output level: 1mV/A to 100 kHz Max. Cond Dia: 2.13" Category: CAT III, 600V  (less)

easy-to-use multimeters are ideally suited to help you with your tasks. Features: Large display with backlight Insulation test: 0.01 M Ohms to 2G Ohms Multiple test voltages: 50V, 100V, 250V, 500V, 1000V Live circuit detection prevents insulation test if voltage &GT30V is detected for added user protection Auto-discharge of capacitive voltage AC/DC voltage, DC mV, AC/DC mA, Resistance (Ohms), Continuity Capacitance, diode test, temperature, min/max, frequency (Hz) Auto power off to save battery Specification Voltage DC Maximum Voltage: 1000 V Accuracy:: ±(0.09%+2) Maximum Resolution: 0.001V Voltage AC Maximum Voltage: 1000 V Accuracy: ±(2%+3) AC Bandwidth: 5kHz with low pass filter; 3db @ 800 Hz Maximum Resolution: 0.1 mV Current DC Maximum Amps: 400mA Amps Accuracy: ±(0.2%+2) Maximum Resolution: 0.01 mA Current AC Maximum Amps: 400mA Amps Accuracy: ±(1.5%+2) 1kHz bandwidth Maximum Resolution: 0.01 mA Resistance Maximum Resistance: 50 MΩ Accuracy: ±(0.9%+2) Maximum Resolution: 0.1O Capacitance Maximum Capacitance: 9,999 µF Accuracy: ±(1.2%+2) Maximum Resolution: 1 nF Frequency Maximum Frequency: 100 kHz Accuracy: ±(0  (less)

Use the Fluke 983 to immediately respond to occupant complaints, or as part of a comprehensive preventive maintenance program. With the Fluke 983, you can: Measure filter efficiency Monitor industrial cleanrooms Pre-screen indoor air quality and confidently work with IAQ specialists Locate particle sources for remediation Report the effectiveness of repairs to customers Drive additional business by demonstrating the need for maintenance and repair With expanded data logging and six-channel particle size display, the Fluke 983 allows users to run more tests quickly, with less time spent cycling through screens to obtain the data. The Fluke 983 is lightweight and easy to use in any position, with a comfortable hand strap and rugged rubber holster. Assess air quality more easily and accurately The Fluke 983 Particle Counter simultaneously measures and displays six channels of particle size distribution, temperature and humidity. This compact, lightweight, self-contained tool allows for one-handed operation. The Fluke 983 maintains its accuracy when used in any position. The 8 hour rechargeable battery together with a large 5000 sample record capacity allows for uninterupted performance during air quality surveys. The Fluke 9  (less)

Test insulation resistance of new electrical equipment during installation or old equipment as preventative maintenance. Features: Measures up to 1 Tera-Ohm Warning voltage function alerts the user that voltage is present and gives a voltage reading up to 1000V AC or DC Cable capacitance Leakage current Ramp function (0-5000VDC) Includes: Test leads, 5000V-rated probes Alligator clips Quickline 1550 PC software Cord Soft carrying case with waterproof bottom User's manual CAT III, 600V Two-Year Warranty (United Kingdom)  (less)